troubleshootint reikia nuo paprasciausiu dalyku, o tu ji cia i kostmosa 
iskelei...

1. bios. ar neuzdrausta.
2. draiveriai. susirast ir sudiegt isnaujo.


jei prie nustatymu nebuta lysta - nx ten net neziuret.

On 2/20/2019 15:36, MRT wrote:
>> Gal kas paziuretu foto ir pasakytu, kur gali buti problema, kad 
>> DOS'inis softas nepamato ISA kontrolerio? Biose viska iskuiciau, 
>> visokius IRQ sujungiau, bet jokio efekto.
>>
>> https://photos.app.goo.gl/JfdLoS9TFhPpLxXm7
> 
> 
> + dar vienas rulonas:
> 
> Pvz. apie ISA garso korta:
> http://www.vogonsdrivers.com/files/Awe32_User_Guide.pdf
> t.y. trauk cia bent jau "autoexec.bat" ir "config.sys" failiukus
> 
> -----------
> 
> If the test program stops or displays an error message when it is
> checking the audio interface’s base I/O address, IRQ line, or DMA
> channels, it may be due to a conflict between the audio interface and
> another peripheral device. To resolve the conflict, you have to change
> the settings of your audio interface. (See the section “Changing
> Resource Settings in Windows 3.1x/DOS” in page 5-6 or Appendix D,
> “Troubleshooting” on how to change the settings and resolve the
> conflicts.)
> 
> The installation program adds the following statements to the
> AUTOEXEC.BAT file.
> SET BLASTER=A220 I5 D1 H5 P330 E620 T6
> SET SOUND=C:\SB16
> SET MIDI=SYNTH:1 MAP:E MODE:0
> C:\SB16\DIAGNOSE /S /W=C:\WINDOWS
> C:\SB16\MIXERSET /P /Q
> C:\SB16\AWEUTIL /S
> 
> 
> The CONFIG.SYS File Settings
> The installation program also adds the following statements to the
> CONFIG.SYS file if you choose to install the low-level DOS device
> drivers under custom installation.
> DEVICE=C:\SB16\DRV\CTSB16.SYS /UNIT=0
> /BLASTER=A:220 I:5 D:1 H:5
> DEVICE=C:\SB16\DRV\CTMMSYS.SYS
> 
> Changing Resource Settings in
> Windows 3.1x/DOS
> 
> <..>
> 
> BLASTER Environment Variable
> The BLASTER environment variable specifies the base I/O address,
> IRQ line, and DMA channel of your audio interface. The syntax for
> the BLASTER environment variable is as follows:
> BLASTER=A220 I5 D1 H5 P330 E620 T6
> 
> Parameter Description
> Axxx Specifies the audio interface’s base I/O address.
> xxx can be 220.
> Ix Specifies the IRQ line used by the audio interface.
> x can be 5.
> Dx Specifies the Low DMA channel used by the audio
> interface. x can be 1.
> Hx Specifies the High DMA channel used by the audio
> interface. x can be 5.
> Pxxx Specifies the MPU-401 UART interface’s base I/O
> address. xxx can be 330.
> Exxx Specifies the Advanced WavEffects chip’s base I/O
> address. xxx can be 620.
> Tx Specifies the card type. x can be 6.
> 
>