pofik kad suformatavai ta harda , i recoveri jei neieina tai gal bandyt su 
usb raktu i service mode ieit , 3.55 dar tai leidzia .



"xkuza" <xkuza@nismo.lt> wrote in message 
news:j4g5gt$eiu$1@trimpas.omnitel.net...
> Ko daryt nereikejo, tai hardo formatuot :D. well, po fakto. Gal kita hdd 
> ps3 nusipirkt? koki sena, tik is playstuchos isimta.
>
> On 9/10/2011 5:28 PM, xkuza wrote:
>> Parsisiunciau 3.55 FW, patikrinau MD5 sumas, atitiko, imeciau i USB
>> rakta, paleidau normaliai updeita is USB rakto, nukopijavo i harda,
>> viskas grazu, ties 70% ismeta errora 8002F14E, kas reiskia system pyzdec.
>>
>> I system recovery moda neisijungia. Istraukiau harda, suformatavau ant
>> kompo. Dabar visai juodas ekranas, lyg hardo nebutu viduje (su salyga,
>> kad fw isimete i hdd is flasho, sakiau ji panaikinsiu is ten).
>>
>> mokejau 60 euru uz ji, i siuksliu deze vpadlu ismest butu :]
>>
>> Kokie galimi problemos sprendimai? Ebay->ant daliu?
>
>
> May be a little late here for some people. But someone after me, could 
> benefit from this information!
> A corrupt NAND PS3 is not the same as a locked in update loop of your PS3. 
> If you see colored dots or other artifacting of icons or Xrossbar, 
> followed by freezing w/o a YLOD, it does mean your PS3 has overheated 
> though. Proof will be when you attempt to go into Recovery Console and run 
> an update or restore fails there as well. Most likely from from over 
> heating or a failed, corrupt or disrupted update, etc. Re-applying heat 
> sink compound could fix this before it does YLOD on you though!
>
> Error 8002F14E Problems:
> If you on the other hand, it's simply locked in an update loop, your PS3 
> can be saved. Sometimes w/ as little as checking all connections and 
> cables or re-seating your hard drive.
>
> Warning!!!
> Whatever you do don't format the hard drive you used in the Update 
> Flashing of your PS3 if it's looping. If you do, it could keep it from 
> ever finishing that update. This is why Sony wants you to send in your 
> hard drive with your PS3 for repairs. In case it's related to this update 
> process. But the actual flashing of PS3's Nand doesn't complete until it 
> reaches 100% and reboots, FYI.
>
> What's happening is that the PS3 is running in Nand flash mode. The Nand 
> (one adjacent to Super Companion/south bridge) has NOT been flashed until 
> this phase is complete. Your PS3 is checking your entire system hardware 
> for faults. If it finds one, then you'll get that 8002F14E code (or 
> similar) and it won't complete until you fix the hardware problem it 
> found. Depending on where in this process it stalls (in the loop % of 
> completion), can indicate where the possible failure is.
>
> Generally if it stalls in the 60-70 range, this indicates a problem with 
> the BluRay (even a dirty lens or bad diode) player in some way. It can be 
> the disc insertion sensor, the main ribbon cable or simply a loose 
> connection. But until you fix it, it will continue to loop in update mode. 
> If it's in 40% range of completion, it can be anything from a bad or loose 
> hdmi connection to fan malfunction, possibly the hard drive (try 
> re-seating harddrive), Power supply (voltage variance or loose 
> connections), WiFi board, USB connector problems, etc!
>
> (for this reason, if somebody wants to sell you a PS3 that is locked in 
> the loop, make absolutely sure that hard drive is included. If not, you 
> will be buying a brick)
>
> If you are out of warranty, then you must decide to on if you are going to 
> open your PS3 up or not. Consider if you are any good at this sort of 
> stuff or not. The PS3 is not hard to tear apart, but you must map things 
> out to know where everything goes back. Inventory your PS3 condition 
> before the update in your mind. Did you have any problems with over 
> heating and shutdowns. Was your PS3 reading all disc types? Any problems 
> accepting discs or ejecting discs? .....and for sure, if you are having 
> ANY hardware issues, then DON'T RUN or give permission/accept the Update 
> until you have these issues resolved!
>
> If you decide to pull your PS3 apart. Do it with care, keeping track of 
> all the screws and where they go. Use a heat gun and razor to carefully 
> remove the warranty sticker, so you can replace it after repairs are done. 
> Make sure you know how to remove and re-insert ribbon cables properly. The 
> BD player needs care in removal. Such as if your model has the tiny fine 
> wires running from the control board to the sensor located on top front. 
> BE EXTRA CAREFUL OF THESE WIRES AND PLUG. DO NOT simply pull the plug from 
> it's socket by the wires. Use finger nails or tweezers to carefully jockey 
> this connection from it's socket.
>
> The BD lens can be cleaned w/o separating the black housing parts. By 
> simply removing the metal case cover, followed by pulling the white 
> magnetic part in the center over the disc rotating motor on top of the 
> black top half. Under toward the back is the laser. Use cotton que-tips 
> and alcohol. Gently first wipe the lens in a circular motion one 
> direction, then the other. Now you would use a dry Que-tip to dry it off 
> with using same technique. USE LIGHT PRESSURE ONLY!
>
> If you decide to pull the whole assembly apart to either clean or replace 
> the diode/lens assembly, then make sure to take note of how things are 
> when you pull it apart and watch some videos on YouTube before trying 
> this. You don't put it back together properly, it may take the disc, but 
> not spin properly and not eject the disc after getting a fail to read it. 
> This can be prevented by observing how you replace the black top assembly. 
> Just prior to setting it down (w/ BD player disc opening facing you), tilt 
> the back of the part toward you, so that the white loose gear part slides 
> down toward the front. You will know it's right by looking at the top, 
> where you'll see two small observation ports (holes). One small w/ one 
> larger one just above it. If you see solid white through these holes, then 
> it's wrong. There is only one white part on the reverse side that is 
> loose. If it didn't slide down on the tilt, then slide it down before 
> replacing it!
>
> That's about it for now. Remember to be patience and use care in this 
> process before you panic!   ....and you just may have your PS3 running 
> again!
>
> NOTE: If you have problems afterward getting the PS3 to recognize the BD 
> player or read discs, take a look at this thread and my comment; "PS3 Disc 
> not spinning." by Dougie085